Iei-integration TANK-GM45A Manuel d'utilisateur

TANK-GM45 Embedded System Page iIEI Technology Corp. User Manual MODEL: TANK-GM45 Wide Range Temperature Fanless Embedded System with VGA, Gigabit

TANK-GM45 Embedded SystemPage 90  Be cautious of all small removable components when vacuuming the TANK-GM45.  Turn the TANK-GM45 off before cle

TANK-GM45 Embedded System Page 91Appendix C C Hazardous Materials Disclosure

TANK-GM45 Embedded SystemPage 92 C.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Merc

TANK-GM45 Embedded System Page 93Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium(Cd) Hexavalent Chromium(CR(VI))

TANK-GM45 Embedded SystemPage 94 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有

TANK-GM45 Embedded System Page 1Chapter 1 1 Introduction

TANK-GM45 Embedded SystemPage 2 1.1 Overview Figure 1-1: TANK-GM45 The TANK-GM45 Series embedded system is a fanless system for wide range temperat

TANK-GM45 Embedded System Page 3 Cost savings with low power consumption 1.4 Features The TANK-GM45 features are listed below:  Intel® 45nm Core

TANK-GM45 Embedded SystemPage 4 Specifications Keyboard/Mouse One PS/2 keyboard/mouse connector Serial Ports 1 x RS-232 (isolated) 1 x RS-422/485 (i

TANK-GM45 Embedded System Page 51.6 Connector Panel All external peripheral interface connectors are located on the front panel of the TANK-GM45 . T

TANK-GM45 Embedded SystemPage 6 1.7 Dimensions The physical dimensions are shown below: Figure 1-3: Physical Dimensions (millimeters)

TANK-GM45 Embedded System Page 7Chapter 2 2 Unpacking

TANK-GM45 Embedded SystemPage 8 2.1 Anti-static Precautions WARNING: Failure to take ESD precautions during installation may result in permanent da

TANK-GM45 Embedded System Page 92.3 Unpacking Checklist NOTE: If some of the components listed in the checklist below are missing, please do not pr

TANK-GM45 Embedded SystemPage ii Revision Date Version Changes 29 August 2011 1.01 Changed the supported processor from Intel® Core2 Duo P8600 to

TANK-GM45 Embedded SystemPage 10 Chapter 3 3 Installation

TANK-GM45 Embedded System Page 113.1 Installation Precautions During installation, be aware of the precautions below:  Read the user manual: The u

TANK-GM45 Embedded SystemPage 12 Figure 3-2: Bottom Panel Retention Screws (Bottom Panel) Step 2: To prevent the internal SATA cable from damage,

TANK-GM45 Embedded System Page 13 Figure 3-4: HDD Bracket Retention Screws Step 4: Attach the HDD bracket to the HDD. Slide the HDD to connect the

TANK-GM45 Embedded SystemPage 14 Step 5: Install the HDD bracket in the same position it was before. Figure 3–6: HDD Installation Step 6: Reinsta

TANK-GM45 Embedded System Page 153.3.1 COM3 RS-422/485 Setup Jumper Label: J5, J9 and J10 Jumper Type: Pin headers Jumper Settings: See Table 3-1, T

TANK-GM45 Embedded SystemPage 16  RS-422/485  USB  VGA Figure 3-7: Peripheral Connectors (Rear) 3.4.1 LAN Connectors CN Label: LAN1 and LAN2 C

TANK-GM45 Embedded System Page 17 Figure 3-8: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cabl

TANK-GM45 Embedded SystemPage 18 Activity/Link LED Speed LED STATUS DESCRIPTION STATUS DESCRIPTION Off No link Off 10 Mbps connection Yellow

TANK-GM45 Embedded System Page 19 Figure 3-11: Power Input Connector Pin Description Pin Description 1 +12V 3 +12V 2 GND 4 GND Table 3-6: Power

TANK-GM45 Embedded System Page iiiCopyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to

TANK-GM45 Embedded SystemPage 20 3.4.5 RS-232 Serial Port Connector CN Label: COM1 CN Type: DB-9 connectors CN Location: See Figure 3-7 CN Pinouts:

TANK-GM45 Embedded System Page 21Pin Description Pin Description 1 DCD 6 DSR 2 RX 7 RTS 3 TX 8 CTS 4 DTR 9 RI 5 GND Table 3-8: COM1 Ser

TANK-GM45 Embedded SystemPage 22 COM 3 RS-485 Description Pin 1 Data- Pin 2 Data+ Table 3-10: RS-485 Pinouts Figure 3-15: Serial Port Pinout

TANK-GM45 Embedded System Page 23 Figure 3-16: USB Device Connection Step 3: Insert the device connector. Once aligned, gently insert the USB devic

TANK-GM45 Embedded SystemPage 24 The VGA connector connects to a monitor that accepts VGA video input. Step 1: Locate the female DB-15 connector. T

TANK-GM45 Embedded System Page 25Pin Description Pin Description 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VCC / NC 10 GND 11 NC

TANK-GM45 Embedded SystemPage 26 Chapter 4 4 BIOS

TANK-GM45 Embedded System Page 274.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system

TANK-GM45 Embedded SystemPage 28 Key Function F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the C

TANK-GM45 Embedded System Page 294.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an ov

TANK-GM45 Embedded SystemPage iv Table of Contents 1 INTRODUCTION...

TANK-GM45 Embedded SystemPage 30 The System Overview field also has two user configurable fields:  System Time [xx:xx:xx] Use the System Time opti

TANK-GM45 Embedded System Page 31BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

TANK-GM45 Embedded SystemPage 32  Frequency: Lists the CPU processing speed  FSB Speed: Lists the FSB speed  Cache L1: Lists the CPU L1 cache

TANK-GM45 Embedded System Page 33 SATA#1 Configuration [Compatible] Use the SATA#1 Configuration option to configure the ATA/IDE controller. Î Dis

TANK-GM45 Embedded SystemPage 34 4.3.2.1 SATA Channel Sets the IDE configuration of the SATA channels. BIOS SETUP UTILITY Main Advanced PCIPNP Bo

TANK-GM45 Embedded System Page 35Î ARMD This option specifies an ATAPI Removable Media Device. These include, but are not limited to: ZIP LS-120 

TANK-GM45 Embedded SystemPage 36 Î Auto DEFAULT BIOS auto detects the PIO mode. Use this value if the IDE disk drive support cannot be determined. Î

TANK-GM45 Embedded System Page 37Î UDMA1 Ultra DMA mode 1 selected with a maximum data transfer rate of 25 MB/s Î UDMA2 Ultra DMA mode 2 selecte

TANK-GM45 Embedded SystemPage 38 4.3.3 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 6) to set or change the configurations

TANK-GM45 Embedded System Page 39 Serial Port3 Address [3E8] Sets the port address of serial port 3.  Disabled  3E8 DEFAULT  2E8  Serial Po

TANK-GM45 Embedded System Page v4.1 INTRODUCTION...

TANK-GM45 Embedded SystemPage 40  Hardware Health Monitoring The following system parameters and values are shown. The system parameters that are

TANK-GM45 Embedded System Page 41BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit AHCI Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

TANK-GM45 Embedded SystemPage 42 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit AHCI Port0 ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

TANK-GM45 Embedded System Page 43BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Configure Remote Access type and paramete

TANK-GM45 Embedded SystemPage 44 NOTE: Make sure the selected COM port is enabled through the Super I/O configuration menu.  Base Address, IRQ [3F

TANK-GM45 Embedded System Page 45 Terminal Type [ANSI] Use the Terminal Type BIOS option to specify the remote terminal type. Î ANSI DEFAULT The t

TANK-GM45 Embedded SystemPage 46 Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a US

TANK-GM45 Embedded System Page 47 Power Supply Status [ATX] Shows the setting of the Power Selection Jumper. 4.4 PCI/PnP Use the PCI/PnP menu (BIO

TANK-GM45 Embedded SystemPage 48  IRQ# [Available] Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral device. Î

TANK-GM45 Embedded System Page 49 DM Channel 5  DM Channel 6  DM Channel 7  Reserved Memory Size [Disabled] Use the Reserved Memory Size BIO

TANK-GM45 Embedded SystemPage vi A.2.2 Create Partitions ...

TANK-GM45 Embedded SystemPage 50 4.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 15) to configure advanced sys

TANK-GM45 Embedded System Page 51 AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory)

TANK-GM45 Embedded SystemPage 52 4.5.2 Boot Device Priority Use the Boot Device Priority menu (BIOS Menu 16) to specify the boot sequence from the a

TANK-GM45 Embedded System Page 534.5.3 Hard Disk Drives Use the Hard Disk Drives menu to specify the boot sequence of the available HDDs. Only insta

TANK-GM45 Embedded SystemPage 54  Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The defaul

TANK-GM45 Embedded System Page 55BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced Chipset Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

TANK-GM45 Embedded SystemPage 56 ISA expansion card is used, please refer to the documentation that came with the card to see if it is necessary to

TANK-GM45 Embedded System Page 57 Restore on AC Power Loss [Last State] Use the Restore on AC Power Loss BIOS option to specify what state the sys

TANK-GM45 Embedded SystemPage 58 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Exit Options ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

TANK-GM45 Embedded System Page 59Appendix A A One Key Recovery

TANK-GM45 Embedded System Page viiList of Figures Figure 1-1: TANK-GM45 ...

TANK-GM45 Embedded SystemPage 60 A.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system

TANK-GM45 Embedded System Page 61A.1.1 System Requirement NOTE: The recovery CD can only be used with IEI products. The software will fail to run a

TANK-GM45 Embedded SystemPage 62 NOTE: Specialized tools are required to change the partition size if the operating system is already installed. A

TANK-GM45 Embedded System Page 63 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. A.2 Setup Procedure for Windows Pri

TANK-GM45 Embedded SystemPage 64 Step 4: Turn on the system. Step 5: Press the <DELETE> key as soon as the system is turned on to enter the

TANK-GM45 Embedded System Page 65Step 3: The recovery tool setup menu is shown as below. Figure A-3: Recovery Tool Setup Menu Step 4: Press <5

TANK-GM45 Embedded SystemPage 66 system32>format F: /fs:ntfs /q /v:Recovery /y system32>exit Figure A-5: Partition Creation Commands

TANK-GM45 Embedded System Page 67 NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to

TANK-GM45 Embedded SystemPage 68 A.2.4 Build-up Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step

TANK-GM45 Embedded System Page 69recovery files in Section 73A.2.2 is hidden and the recovery tool is saved in this partition. Figure A-8: Build-up

TANK-GM45 Embedded SystemPage viii Figure A-9: Press any key to continue ...

TANK-GM45 Embedded SystemPage 70 A.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to

TANK-GM45 Embedded System Page 71 Figure A-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (73Figure A-13).

TANK-GM45 Embedded SystemPage 72 Figure A-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown in 7

TANK-GM45 Embedded System Page 73 Figure A-16: File Name to Copy Image to Step 8: When the Compress Image screen in 73Figure A-17 prompts, click Hi

TANK-GM45 Embedded SystemPage 74 Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure A-18: Image Creat

TANK-GM45 Embedded System Page 75Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step 0: Fig

TANK-GM45 Embedded SystemPage 76 NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure A-22: Partitions for Linux

TANK-GM45 Embedded System Page 77 Figure A-23: System Configuration for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst

TANK-GM45 Embedded SystemPage 78 Step 7: The recovery tool menu appears. (74Figure A-25) Figure A-25: Recovery Tool Menu Step 8: Create a factor

TANK-GM45 Embedded System Page 79Figure A-26: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restor

TANK-GM45 Embedded System Page ixList of Tables Table 1-1: TANK-GM45 Model Variations...

TANK-GM45 Embedded SystemPage 80 A.4.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1>

TANK-GM45 Embedded System Page 81A.4.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press <Ente

TANK-GM45 Embedded SystemPage 82 A.4.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <

TANK-GM45 Embedded System Page 83A.4.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press &l

TANK-GM45 Embedded SystemPage 84 A.5 Other Information A.5.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHCI mode

TANK-GM45 Embedded System Page 85Step 5: When the following window appears, press <S> to select “Specify Additional Device”. Step 6: In the

TANK-GM45 Embedded SystemPage 86 Step 7: After pressing <Enter>, the system will get into the recovery tool setup menu. Continue to follow th

TANK-GM45 Embedded System Page 87Appendix B B Safety Precautions

TANK-GM45 Embedded SystemPage 88 B.1 Safety Precautions WARNING: The precautions outlined in this appendix should be strictly followed. Failure to

TANK-GM45 Embedded System Page 89B.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the TANK-GM45 ma