Iei-integration NANO-LX v1.00 Manuel d'utilisateur télécharger pdf (Page 81)

NANO-LX CPU Card

Figure 3-33: Jumper Locations

NOTE:

The NANO-LX does not provide a “Clear CMOS” configuration jumper. If the system fails

to boot due to improper BIOS settings, reset the CMOS contents by disconnecting and

reconnecting the BT1 battery connector. Use small-sized needle nose pliers to carefully

disconnect and reconnect the BT1 battery connector.

1 2 ... 76 77 78 79 80 81 82 83 84 85 86 ... 210 211

Table of Contents 3
List of Figures 8
List of Tables 11
List of BIOS Menus 13
Glossary 14
Introduction 15
Detailed Specifications 21
2.3 Graphics Support 26
2.4 Memory Support 27
2.6 Ethernet 27
2.15 Power Consumption 32
Connectors and Jumpers 35
3.2.2 ATX Connector 42
3.2.6 Battery Connector 47
3.2.9 Fan Connector 51
3.2.15 LED Power Connector 60
3.2.18 PC/104-Plus Connector 64
3.2.20 Power Input Connector 68
3.2.22 SATA Drive Ports 71
3.2.24 TFT TTL LCD Connector 74
3.3.1 RS232 Serial Connector 76
3.3.2 VGA Connector 77
3.3.3 Ethernet Connector 78
NOTE: 80
Installation and 87
Configuration 87
4.1.1 Installation Notices 88
4.2 Unpacking 89
WARNING! 90
 SO-DIMM module 91
Step 2: 92
Step 3: 92
Step 4: 92
4.3.4.3 Compact Flash Disk 95
Award BIOS Setup 97
5.1 Introduction 98
NANO-LX CPU Card 101
5.2 Standard CMOS Features 102
 IDE Primary Master 102
 IDE Primary Slave 102
Primary Master 104
 Channel 0 Master 105
 Channel 0 Slave 105
 Channel 1 Master 105
5.3 Advanced BIOS Features 107
NTER and the 113
 Disabled (Default) 117
 3F8/IRQ4 117
 2F8/IRQ3 117
 3E8/IRQ4 117
 2E8/IRQ3 117
 Active Only 120
 Free running (Default) 120
5.5 Integrated Peripherals 120
 Master Drive PIO Mode 121
 Slave Drive PIO Mode 121
 IDE Primary Master UDMA 121
 IDE Primary Slave UDMA 121
 Disabled 125
 378/IRQ7 (Default) 125
 278/IRQ5 125
 3BC/IRQ7 125
5.6 Power Management Setup 128
5.7 PnP/PCI Configurations 131
 Reserved Memory Base 134
 Reserved Memory Length 134
5.8 PC Health Status 136
 CPU Fan Speed 136
Software Drivers 139
Step 1: 140
Technology, Corp 142
6.2 VGA Driver 143
Step 5: 145
6.4 LAN Driver 157
6.5 SATA/RAID Driver 161
6.6 ISA Driver 166
BIOS Configuration 173
Options 173
Watchdog Timer 179
Address Mapping 183
C.1 I/O Address Map 184
MB Memory Address Map 184
C.3 IRQ Mapping Table 185
C.4 DMA Channel Assignments 185
External AC’97 Audio 187
D.1 Introduction 188
RAID for SATA 193
E.1 Introduction 194
E.4 RAID BIOS Setup Utility 196
E.5 RAID Options: 196
 64K (default) 202
Connecting an ATX 205
Power Supply 205
Figure F-1: Jumper Locations 206

Commentaires sur ces manuels

Pas de commentaire

Iei-integration NANO-LX v1.00 Manuel d'utilisateur Page 81

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Iei-integration NANO-LX v1.00