Iei-integration TANK-101B-D525_N455 v1.00 Manuel d'utilisateur

TANK-101B/BW Embedded Sys tem Page i IEI Technology Corp. User Manual MODEL: TANK-101B/BW Fanless Embedded System with Intel® Atom™ D525/N455 CPU,

TANK-101B/BW Embedded System Page x Lis t of Tables Table 1-1: TANK-101B/BW Model Variations ...

TANK-101B/BW Embedded System Page 90 A.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in re

TANK-101B/BW Embedded System Page 91 filename “pxelinux.0”; A.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum inst

TANK-101B/BW Embedded System Page 92 Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/in

TANK-101B/BW Embedded System Page 93 A.6.4 Start the DHCP, TFTP and HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart

TANK-101B/BW Embedded System Page 94 Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public

TANK-101B/BW Embedded System Page 95 Step 2: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1  re

TANK-101B/BW Embedded System Page 96 NOTE: A firewall or a SELinux is not in use in the whole setup process. If there is a firewall or a SELinu

TANK-101B/BW Embedded System Page 97 A.7 Other Information A.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHCI m

TANK-101B/BW Embedded System Page 98 Step 5: When the following window appears, press <S> to select “Specify Additional Device”. Step 6: I

TANK-101B/BW Embedded System Page 99 Step 7: After pressing <Enter>, the system will get into the recovery tool setup menu. Continue to follo

TANK-101B/BW Embedded System Page 1 Chapter 1 1 Introduction

TANK-101B/BW Embedded System Page 100 Appendix B B Safety Precautions

TANK-101B/BW Embedded System Page 101 B.1 Safety Precautions WARNING: The precautions outlined in this appendix should be strictly followed. Failu

TANK-101B/BW Embedded System Page 102 B.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the TANK-1

TANK-101B/BW Embedded System Page 103 B.1.3 Product Disposal CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certifie

TANK-101B/BW Embedded System Page 104  The interior of the TANK-101B/BW does not require cleaning. Keep fluids away from the TANK-101B/BW interior

TANK-101B/BW Embedded System Page 105 Appendix C C Hazardous Materials Dis clos ure

TANK-101B/BW Embedded System Page 106 C.1 Hazardous Materials Disclosure Ta b le for IPB Products Certified as RoHS Compliant Under 2002/95/EC With

TANK-101B/BW Embedded System Page 107 Part Name Toxic or Hazardous Substances and Elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium

TANK-101B/BW Embedded System Page 108 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品

TANK-101B/BW Embedded System Page 2 1.1 Overview Figure 1-1: TANK-101B/BW The TANK-101B/BW fanless embedded system is powered by the Intel® Atom™

TANK-101B/BW Embedded System Page 3 1.3 Features The TANK-101B/BW features are listed below:  Intel® Atom™ D525 1.8 GHz/N455 1.66 GHz processor 

TANK-101B/BW Embedded System Page 4 Specifications USB 4 x USB 2.0 ports Dis play 1 x VGA port Resolution Up to 2048x1536 @ 60 Hz (D525 model) Up to

TANK-101B/BW Embedded System Page 5 1.5 Connector Panel 1.5.1 Front Panel The TANK-101B/BW front panel contains:  2 x CAN-bus ports with isolation

TANK-101B/BW Embedded System Page 6 1.5.2 Rear Panel The TANK-101B/BW rear panel contains:  1 x VGA output  3 x RS-232 serial ports (COM4: With

TANK-101B/BW Embedded System Page 7 1.6 Dimensions The physical dimensions are shown below: Figure 1-4: Physical Dimensions (millimeters)

TANK-101B/BW Embedded System Page 8 Chapter 2 2 Unpacking

TANK-101B/BW Embedded System Page 9 2.1 Anti-static Precautions WARNING: Failure to take ESD precautions during installation may result in permane

TANK-101B/BW Embedded System Page ii Revis ion Date Version Changes 14 March 2013 1.00 Initial release

TANK-101B/BW Embedded System Page 10 2.3 Unpacking Checklist NOTE: If some of the components listed in the checklist below are missing, please do n

TANK-101B/BW Embedded System Page 11 Quantity Item and Part Number Im a g e Standard 1 Screw set 1 One Key Recovery CD 1 User manual and dri

TANK-101B/BW Embedded System Page 12 Chapter 3 3 Ins tallation

TANK-101B/BW Embedded System Page 13 3.1 Installation Precautions During installation, be aware of the precautions below:  Read the user manual: T

TANK-101B/BW Embedded System Page 14 The equipment is intended for installation in a RESTRICTED ACCESS LOCATION.  Access can only be gained by SER

TANK-101B/BW Embedded System Page 15 Figure 3-2: CF Card Installation 3.3 Hard Dis k Drive (HDD) Ins tallation To install the hard drive, please fo

TANK-101B/BW Embedded System Page 16 Step 3: Attach the HDD to the HDD bracket, and then slide the HDD to connect the HDD to the SATA connector (Fi

TANK-101B/BW Embedded System Page 17 Figure 3-5: Retention Screw Holes Step 3: Secure the brackets to the system by inserting two retention screws

TANK-101B/BW Embedded System Page 18 Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into the four pilot holes an

TANK-101B/BW Embedded System Page 19 Figure 3-7: Mount the Embedded System

TANK-101B/BW Embedded System Page iii Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order

TANK-101B/BW Embedded System Page 20 3.6 J umper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of tw

TANK-101B/BW Embedded System Page 21 3.7 External Peripheral Interface Connectors The TANK-101B/BW has the following connectors. Detailed descriptio

TANK-101B/BW Embedded System Page 22 3.7.2 CAN-bus Connectors CN Type: DB-9 connector CN Location: See Figure 1-2 CN Pinouts: See Table 3-2 and F

TANK-101B/BW Embedded System Page 23 Step 1: Locate the RJ-45 connectors. The locations of the RJ-45 connectors are shown in Figure 1-3. Step 2: A

TANK-101B/BW Embedded System Page 24 Figure 3-11: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yell

TANK-101B/BW Embedded System Page 25 3.7.6 RS-232 Serial Port Connectors CN Label: COM1, COM2 and COM4 CN Type: DB-9 connectors CN Location: See

TANK-101B/BW Embedded System Page 26 Pin Description Pin Description 3 TX 8 CTS 4 DTR 9 RI 5 GND Table 3-5: RS-232 Serial Port Pinouts

TANK-101B/BW Embedded System Page 27 5 GND GND 6 N/A N/A 7 N/A N/A 8 N/A N/A 9 N/A N/A Table 3-6: RS-422/485 Serial Port Pinouts Figure

TANK-101B/BW Embedded System Page 28 Figure 3-16: USB Device Connection Step 3: Insert the device connector. Once aligned, gently insert the USB d

TANK-101B/BW Embedded System Page 29 The VGA connector connects to a monitor that accepts VGA video input. Step 1: Locate the female DB-15 connecto

TANK-101B/BW Embedded System Page iv Ta b le of Contents 1 INTRODUCTION ...

TANK-101B/BW Embedded System Page 30 Pin Description Pin Description 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VCC / NC

TANK-101B/BW Embedded System Page 31 Chapter 4 4 BIOS

TANK-101B/BW Embedded System Page 32 4.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain sy

TANK-101B/BW Embedded System Page 33 Key Function Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page S

TANK-101B/BW Embedded System Page 34 4.2 Ma in The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives

TANK-101B/BW Embedded System Page 35  System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes

TANK-101B/BW Embedded System Page 36 4.3.1 ACPI Settings The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and Power Inter

TANK-101B/BW Embedded System Page 37 4.3.2 Trusted Computing Use the Trusted Computing menu (BIOS Menu 4) to configure settings related to the Trus

TANK-101B/BW Embedded System Page 38 Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced CPU Configuration Processo

TANK-101B/BW Embedded System Page 39 Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced PATA Master Not Present PA

TANK-101B/BW Embedded System Page v 3.7.7 RS-422/485 Serial Port Connector ... 26 3.7

TANK-101B/BW Embedded System Page 40 4.3.5 USB Configuration Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information and

TANK-101B/BW Embedded System Page 41  Disabled Legacy USB support disabled  Auto Legacy USB support disabled if no USB devices are connected 4

TANK-101B/BW Embedded System Page 42 4.3.6.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 9) to configure the ser

TANK-101B/BW Embedded System Page 43  IO=3F8h; IRQ=3, 4 Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4  IO=2F8h; IRQ=3

TANK-101B/BW Embedded System Page 44  IO=2C8h; IRQ=3, 4 Serial Port I/O port address is 2C8h and the interrupt address is IRQ3, 4 4.3.6.1.3 Seria

TANK-101B/BW Embedded System Page 45 4.3.6.1.4 Serial Port 4 Configuration  Serial Port [Enabled] Use the Serial Port option to enable or disable

TANK-101B/BW Embedded System Page 46 4.3.7 H/W Monitor The H/W Monitor menu (BIOS Menu 10) shows the operating temperature, fan speeds and system vo

TANK-101B/BW Embedded System Page 47 o Vcc1_5VDDR o VSB3V o VBAT  CPU Smart Fan control [Auto Mode] Use the CPU Smart Fan control option to con

TANK-101B/BW Embedded System Page 48 Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced COM1 Console Redirection

TANK-101B/BW Embedded System Page 49  Bits per second [115200] Use the Bits per second option to specify the serial port transmission speed. The s

TANK-101B/BW Embedded System Page vi A.2 SETUP PROCEDURE FOR WINDOWS ... 63 A

TANK-101B/BW Embedded System Page 50 4.4.1 Hos t Bridge Configuration Use the Host Bridge Configuration menu (BIOS Menu 13) to configure the Northbr

TANK-101B/BW Embedded System Page 51 4.4.1.1 OnChip VGA Configuration Use the OnChip VGA Configuration menu (BIOS Menu 14) to configure the OnChip

TANK-101B/BW Embedded System Page 52 Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Chipset Auto Power Button Function

TANK-101B/BW Embedded System Page 53  Disabled USB function support disabled  Enabled DEFAULT USB function support enabled  USB 2.0 (EHCI)

TANK-101B/BW Embedded System Page 54  DVMT Mode Select [DVMT Mode] Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Techno

TANK-101B/BW Embedded System Page 55  Bootup NumLock State [On] Use the Bootup NumLock State BIOS option to specify if the number lock setting mus

TANK-101B/BW Embedded System Page 56 Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save &am

TANK-101B/BW Embedded System Page 57 4.7 Exit Use the Exit menu (BIOS Menu 19) to load default BIOS values, optimal failsafe values and to save conf

TANK-101B/BW Embedded System Page 58  Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults.

TANK-101B/BW Embedded System Page 59 Appendix A A One Key Recovery

TANK-101B/BW Embedded System Page vii ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ... 106

TANK-101B/BW Embedded System Page 60 A.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost sys

TANK-101B/BW Embedded System Page 61 After completing the five initial setup procedures as described above, users can access the recovery tool by pr

TANK-101B/BW Embedded System Page 62 partitions. Please take the following table as a reference when calculating the size of the partition. OS O

TANK-101B/BW Embedded System Page 63 o Ubuntu 8.10 (Intrepid) o Ubuntu 7.10 (Gutsy) o Ubuntu 6.10 (Edgy) o Debian 5.0 (Lenny) o Debian 4.0 (Etc

TANK-101B/BW Embedded System Page 64 A.2.1 Hardware and BIOS Setup Step 1: Make sure the system is powered off and unplugged. Step 2: Install a ha

TANK-101B/BW Embedded System Page 65 Figure A-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below. Figure A-3

TANK-101B/BW Embedded System Page 66 Figure A-4: Command Mode Step 5: The command prompt window appears. Type the following commands (marked in re

TANK-101B/BW Embedded System Page 67 Figure A-5: Partition Creation Commands

TANK-101B/BW Embedded System Page 68 NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any k

TANK-101B/BW Embedded System Page 69 A.2.4 Build-up Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system.

TANK-101B/BW Embedded System Page viii Lis t of Figures Figure 1-1: TANK-101B/BW ...

TANK-101B/BW Embedded System Page 70 Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In

TANK-101B/BW Embedded System Page 71 A.2.5 Create Factory Default Im a g e NOTE: Before creating the factory default image, please configure the

TANK-101B/BW Embedded System Page 72 Figure A-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (778H778HFig

TANK-101B/BW Embedded System Page 73 Figure A-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown

TANK-101B/BW Embedded System Page 74 Figure A-16: File Name to Copy Image to Step 8: When the Compress Image screen in 782H782HFigure A-17 prompts

TANK-101B/BW Embedded System Page 75 Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure A-18: Image C

TANK-101B/BW Embedded System Page 76 Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. St ep 0:

TANK-101B/BW Embedded System Page 77 Figure A-22: Auto Recovery Utility Step 3: Reboot the system from the recovery CD. When prompted, press any k

TANK-101B/BW Embedded System Page 78 Step 5: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partitio

TANK-101B/BW Embedded System Page 79 Step 7: The Symantec Ghost starts to create the factory default image (Figure A-27). Figure A-27: Image Creat

TANK-101B/BW Embedded System Page ix Figure A-9: Press Any Key to Continue ...

TANK-101B/BW Embedded System Page 80 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit iEi Feature  Au

TANK-101B/BW Embedded System Page 81 Step 2: Install Linux operating system. Make sure to install GRUB (v0.97 or earlier) MBR type and Ext3 partiti

TANK-101B/BW Embedded System Page 82 DISKPART>create part pri size= ___ DISKPART>assign letter=N DISKPART>exit system32>format N:

TANK-101B/BW Embedded System Page 83 Figure A-31: Access menu.lst in Linux (Text Mode) Step 6: Modify the menu.lst as shown below. Step 7: The

TANK-101B/BW Embedded System Page 84 A.5 Recovery Tool Functions After completing the initial setup procedures as described above, users can access

TANK-101B/BW Embedded System Page 85 WARNING: All data in the system will be deleted during the system recovery. Please backup the system files be

TANK-101B/BW Embedded System Page 86 Figure A-35: Recovery Complete Window A.5.2 Backup System To backup the system, please follow the steps below.

TANK-101B/BW Embedded System Page 87 Figure A-37: System Backup Complete Window A.5.3 Restore Your Last Backup To restore the last system backup, p

TANK-101B/BW Embedded System Page 88 Figure A-39: Restore System Backup Complete Window A.5.4 Manual To restore the last system backup, please foll

TANK-101B/BW Embedded System Page 89 A.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automaticall